IJSER Home >> Journal >> IJSER
International Journal of Scientific and Engineering Research
ISSN Online 2229-5518
ISSN Print: 2229-5518 10    
Website: http://www.ijser.org
scirp IJSER >> Volume 3,Issue 10,October 2012
Tooth-Bending Effects in Plastic Spur Gears Influence on load sharing, stresses and wear
Full Text(PDF, )  PP.192-199  
Author(s)
Asst.Prof.Subburaj Ramasamy
KEYWORDS
Consequences, FEA, Gear teeth, Kinematics, Load sharing, PV Pressure Velocity, Stresses.
ABSTRACT
This describes the investigation of a steel-and-plastic gear transmission, using both numerical (FE) and analytical methods. The aim was to study the influence of the stiffness of the gear material on the bending of the gear teeth, and the consequences on
References
[1] Klein, G. “Untersuchungen zur T r a g f ä h i g k e i t t h e r m o p l a s t i s c h e r Kunststoffzahnräder.” Konstruktion 20 (1968) pp. 385–390.

[2] Cornelius, E.A. and W. Budich. “Untersuchungen an Zahnrädern aus AcetalharzenKonstruktion 22 (1970) pp. 103–116.

[3] B u di c h , W . “ E r g e b n i s s e v o n V e r s u c h e n a n G e s c h m i e r t e n T h e r m o p l a s t i s c h e n .Z a h n rädern. Konstruktion 22 (1970) pp.96–401.

[4] B e i t z , W . a n d E . S i e d k e . “Untersuchungen an Zahnrädern aus Polyamid 12.” Kunststoffe 62 (1972) pp. 390-393.

[5] Severin, D. and H. Lütkebohle. “Wälzreibung zylindrischer Räder aus Kunststoff.” Konstruktion 38 (1986) pp. 173–179.

[6] S e v e r i n , D . a n d B . K ü h l k e n . “Tragfähigkeit von Kunststoffrädern u n t e rB e r ü c k s i c h t i g u n gd er Eigenerwärmung.” Konstruktion 43 (1991) pp. 153 160.

[7] B a u m g a r t , J . “ T r a g f ä h i g k e i t m o d i f i z i e r t e r K u n s t s t o f f / S t a h l -Zahnradpaarungen.” Konstruktion 43 (1991) pp. 378 384

[8] Chen, Q.T. “Flankenbeanspruchung bei Stirnzahnrädern aus Kunststoffen.” Konstruktion 43 (1991) pp. 225 232

[9] H o m a n n , H . V D I , A b t e i l u n g Richtlinien. Personal Communication, October 2004.

[10] Y el l e , H . a n d D . J . B u r n s . “Calculation of Contact Ratios for Plastic/Plastic and Plastic/Steel Spur Gear Pairs.” Journal of Mechanical Design 103 (1981) pp. 528–542.

[11] Walton, D., A.A. Tessema, C.J. H o o k e a n d J . M . S h i pp e n . “ L o a d Sharing in Metallic and Non-Metallic Gears.” Proc. Inst. Mech. E, Part C: Journal of Mechanical Engineering Science 208 (1994) pp. 81–87.

[12] Arafa, M.H. and M.M. Megahed. “ E v a l u a t i o n o f S p u r G e a r M e s h ComplianceUsing Finite Element Method.” Proc. Inst. Mech. E, Part C: Journal of Mechanical Engineering Science 213 (1999) pp. 569–579.

[13] T s a i , M . H . a n d Y . C . T s a i . “A Method for Calculating Static Transmission Errors of Plastic Spur Gears Using FEM Evaluation.” Finite Elements in Analysis and Design 27 (1999) pp. 345–357.

[14] Litvin, F.L., L. Qiming and A.L. Kapelevich. “Asymmetric Modified Spur Gear Drives: Reduction of Noise Localization of Contact, Simulation of Meshing and Stress Analysis.”

[15] Comput. Methods Appl. Mech. Engrg. 188 (2000) pp. 363–390.

[16] Walton, D., A.A. Tessema, C.J. Hooke and J.M. Shippen. “A Note on Tip Relief and Backlash Allowances in Non-Metallic Gears.” Proc. Inst. Mech. E, Part C: Journal of Mechanical EngineeringScience 209 (1994) pp.383–388

[17] M a o , K . , C . J . H o o k e a n d D . W a l t o n . “ T h e W e a r B e h a v i o r o f Polymer Composite Gears.” Synthetic Lubrication 12 (1996) pp. 337–342.

[18] Breeds, A.R., S.N. Kukureka, K. Mao, D. Walton and C.J. Hooke. “Wear behavior of Acetal Gear Pairs” Wear 166 (1993) pp. 85–91.

[19] White, J., D. Walton and D.J. Weale. “The Beneficial Effect of Tip Relief On Plastic Spur Gears.” ANTEC Conf. Proc. Society Plastics Engineers 3 (1998) pp. 3013–3107

Untitled Page