IJSER Home >> Journal >> IJSER
International Journal of Scientific and Engineering Research
ISSN Online 2229-5518
ISSN Print: 2229-5518 10    
Website: http://www.ijser.org
scirp IJSER >> Volume 2, Issue 10, October 2011 Edition
Direct Torque Control Of Permanent Magnet Synchronous Motor
Full Text(PDF, 3000)  PP.  
Author(s)
Simhadri Amarendra Babu
KEYWORDS
Conventional Direct Torque Control System, Conclusion, Direct Torque Control (DTC) Of PMSM Drive, Introduction, Mathematical Modeling Of Permanent Magnet Synchronous Motor, Reference, Simulation Results, Voltage Vector Selection In DTC Of PMSM Drive
ABSTRACT
Permanent Magnet synchronous motors (PMSMs) are used in many applications that require rapid torque response and high-performance operation. The PMSM is very similar to the standard wound rotor synchronous machine except that the PMSM has no damper windings and excitation is provided by a permanent magnet instead of a field winding. The elimination of field coil, dc supply and slip rings reduce the motor loss and complexity. For the same frame size, permanent magnet motors have higher pull out torque. It is mathematically proven that the increase of electromagnetic torque in a permanent magnet motor is proportional to the increase of the angle between the stator and rotor flux linkages, and, therefore, the fast torque response can be obtained by adjusting the rotating speed of the stator flux linkage as fast as possible. This is achieved by using direct torque control (DTC) technique.
References
[1] Direct Torque Control of Permanent Magnet Synchronous Motor with Reduced Torque Ripple and Commutation Frequency Yongchang Zhang, Member, IEEE, Jianguo Zhu, Senior Member, IEEE

[2] M. Depenbrock, “Direct Self – Control (DSC) of Inverter Fed Induction Machine”, IEEE Trans. Power Electronics, Vol. 3, No 4, October 1988.

[3] Simulation of Permanent Magnet Synchronous Motor Drive system”, Ph.D thesis, University of Puerto Rico Mayagüez campus, 2006.

[4] Cui Bowen, Zhou Jihua, Ren Zhang, “Modeling and Simulation of Permanent Magnet Synchronous Motor Drive” Fifth IEEE International Conference on Electrical Machines and Systems, Volume 2, Aug. 2001.

[5] S. Morimoto, Y. Tong, Y. Takeda, and T. Hirasa, ""Loss minimization control of permanent magnet synchronous motor drives,"" Industrial Electronics, IEEE Transactions on, vol. 41, pp. 511-517, 1994.

[6] L. Zhong, M. F. Rahman, W.Y. Hu, K.W. Lim, “Analysis of Direct Torque Control in Permanent Magnet Synchronous Motor Drive”, IEEE Trans. On Power Electronics, Vol. 12, No.3, May, 1997.

[7] D.Casadei, Francesco Profumo, Giovanni Serra, Angelo Tanni, “FOC and DTC: two viable schemes for Induction Motor Torque control”, IEEE transactions on Power Electronics. 2002.

[8] LANG Bao-hua, LIU Wei-guo, ZHOU Xi-wei, LI Rong, “Research on Direct Torque Control of Permanent Magnet Synchronous Motor Based on Optimized State Selector”, IEEE ISIE Volume 3, 9-13 July 2006.

[9] Rahman MF, Zhong L. “Voltage switching tables for DTC controlled interior permanent magnet motor”, IECON’99, 25th annual Conference June, 1999.p. 1445–51.

[10] Jurgen K. Steinke “Control strategy for three phase AC traction Drive with Three-level GTO-PWM inverter”, PESC.1988.

[11] Thomas G. Habetler and Deepakraj M. Divan “Control strategies for Direct Torque Control using Discrete Pulse Modulation”, IEEE transactions on Industrial applications, VOL.27 page(s). 893-901.1991.

[12] Chapuis, Y.A.; Roye, D.; Davoine, J “Principles and implementation of direct torque control by stator flux orientation of an induction motor”, Applied Power Electronics conference proceedings, vol.1 Page(s):185 – 191. 1995.

[13] Xavier del Toro Garcia, Antoni Arias, Marcel G. Jayne, Phil A. Witting, Vicenç M. Sala, Jose Luis Romeral “New DTC Control Scheme for Induction Motors fed with a Three-level Inverter”, AUTOMATIKA, Pages 73–81.2005.

[14] T.-W. Chun, M.-K. Choi, and B. K. Bose, “A novel startup scheme of statorflux- oriented vector-controlled induction motor drive without torque jerk,” IEEE Trans. Ind. Appl.,vol.39,no.3, pp. 776–782, May 2003.

[15] T. Habetler, F. Profumo, M. Pastorelli, and L. Tolbert, “Direct torque control of induction machines using space vector modulation,” IEEE Trans. Ind. Appl., vol. 28, no. 5, pp. 1045 –1053, sep/oct 1992.

[16] M. Pacas and J. Weber, “Predictive direct torque control for the PM synchronous machine,” IEEE Trans. Ind. Electron., vol. 52, no. 5, pp.1350 – 1356, oct. 2005.

[17] D. Casadei, F. Profumo, G. Serra, and A. Tani, “FOC and DTC: two viable schemes for induction motors torque control,” IEEE Trans. PowerElectron., vol. 17, no. 5, pp. 779–787, Sep. 2002.

[18] G. Foo and M. F. Rahman, “Sensorless direct torque and flux-controlled IPM synchronous motor drive at very low speed without signal injection,” IEEE Trans. Ind. Electron., vol. 57, no. 1, pp. 395–403, Jan. 2010

Untitled Page