ICEDET 2017- International Conference on Emerging developments in Engineering & Technology

"ICEDET 2017 Conference Papers "

Pages   [1] [2]
 

Numerical Investigation of Natural Convection Heat Transfer Rate For Heat Sink[ ]


In this paper Heat Transfer Rate is investigated for Vertical Cylinder attached with Vertical Oriented Fins (Heat Sink) for natural convection using ANSYS. For this purpose three cases are considered. Here analysis is carried out for 3 types of heat sinks (by changing their height with same number of fins).Temperature Contours and Heat Flux Contours are studied for these three cases, in which it is observed that temperature is maximum in the inner portion of heat sink where heater is inserted and minimum at the outer portion of it. Convection is maximum at outer portion of vertical oriented fins which are attached to the cylinder. Heat transfer rate is calculated using the results of heat flux contours and it is maximum for heat sink with N=12, H=30mm for given input parameters.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Designing and Fabrication of Green Vintage Car[ ]


Design and fabrication of an electric operated car named as “GREEN VINTAGE CAR”is described in this paper. It is a car which will operate completely on electricity with the help of a DC motor and a rechargeable battery. In this project,authors are trying to give this tech a new feature like a constant speed switch which will keep the car going with a constant speed without using the accelerator.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
EXPERIMENTAL INVESTIGATION OFTHERMAL PERFORMANCE IN HEAT EXCHANGERTUBE FOR DOUBLE SIDED DELTA WING WITH BOTH SIDE SERRATIONINSERT[ ]


In the present study the experimental investigation of heat transfer properties for double sided delta wing with both side serration(backward arrangement) insertin heat exchanger tube. The heat transfer, friction factor and thermal performance of the heat exchanger tube isinvestigated at constant heat flux and steady state conditions.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
A Review on Biodiesel Asa Alternative Fuel[ ]


Recycle of waste cooking oil is harmful for health, as it is not environmental friendly to disposed used cooking oil. The best way is to use it for making biodiesel. The biodiesel is blended with diesel oil to get B5 and B10 grade fuel.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
A Review Of Using Nonedible Oils For IC Engine[ ]


This review will be purposeful on the application of vegetable oils produced from the biomass (triglyceriedes) to internal combustion (IC) engines such as compression ignition (CI) engine. The use of inedible vegetable oils as an alternative fuel for diesel engine, they use in energy conversion systems lower the impact, from the economic, energetic and environmental points of view, with respect to biodiesel production.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
A Review Conversion of pine needle from threat to economic opportunity[ ]


This paper accounts for a methodology to address the management of forest bio residue i.e. pine needles and pine cones in Himalayan region of India .As we know that the population is increasing day by day and we don’t have enough energy to meet the demand so in this case pine needles and pine cones can be used as a non conventional sources of energy .

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
A Review on Pine Needle and Its Potential to Develop Energy[ ]


Pine trees cover large areas of the Kumaon Hills and are considered a threatening to cultivation and agriculture as well as the environment. Because during the summer season, pine needles continuously fall from the pine trees and most of the ground surface is covered by pine needles and pine cones. This leads to cause of uncontrolled forest fire and it also affect the wildlife and environment also.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
A scientific Approach of zero inventories by using Just in Time approach[ ]


In the early 1980’s, a number of US firms followed the pioneering efforts of Shigeo Shingo and Taichi Ohno and adopted Just-In-Time (JIT) manufacturing in an attempt to reshape their manufacturing environments. JIT requires that a company have a few reliable suppliers and is believed to enhance productivity and build a leaner manufacturing system which minimizes inventories and reduces which reduces risk and helps minimize the cost of manufacturing.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
A Review on thermal analysis and modelling techniques of Die Sinking Electric Discharge Machine[ ]


Electric Discharge Machining also known as spark machining is widely used in production where required shape is obtained using sparks. Material is removed from the work piece by a series of rapidly frequent current which forms discharge or spark between electrode and work piece, separated by a dielectric liquid.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
A Novel Approach for Simulation of Fixed Bed Regenerator[ ]


Fixed-bed regenerators are compact heat exchangers in which heat is absorbed from the high temperature flue gases and released to the low temperature inlet gas using high heat capacity material matrix. The heat transfer in the fixed bed heat exchangers is govern by the coupled partial differential equations(PDEs).

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Simulation of Natural-Convection in Air-Cooling Electronic Components Mounted in a Horizontal Channel[ ]


In this investigation due to advancement in high–speed computers and different electronic components, heat transfer rate at the microchip is becoming a source of concern. Cooling is necessary for increasing the reliability and functionality of electronic components. Cooling of 2 to 5 identical heat sources mounted in a two-dimensional horizontal channel by natural convection air cooling is shown in present work.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
INVESTIGATION AND ANALYSIS OF METAL CASTING DEFECT BY USING QUALITY CONTROL TOOLS ON TRUMPET HOUSING OF A TRACTOR: A CASE STUDY[ ]


Casting is very versatile process used in a number of engineering applications. One of the application is in the production of Trumpet Housing used in a tractor for supporting its rear axle shafts. But due to poor quality of the foundry industryit has become difficult to meet defect free and strict delivery schedule in the production process.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
CFD ANALYSIS ON SOLAR AIR HEATER WITH ARTIFICIAL ROUGHENED BROKEN CURVED RIBS[ ]


Solar air heaters provides the efficient use of solar energy, which uses the absorber plate to absorb the incoming solar radiations, converting it to thermal energy at its surface, and transferring the thermal energy to the fluid flowing through the collector. It has been observed that the efficiency of the flat plate solar air heater is low because of low convective heat transfer coefficient between the absorber plate and the air flowing over it.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
STUDY AND ANALYSIS OF SOLAR AIR HEATER WITH ARTIFICIAL ROUGHENED BROKEN SINUSOIDAL RIBS[ ]


Solar air heaters provides the efficient use of solar energy, which uses the absorber plate to absorb the incoming solar radiations, converting it to thermal energy at its surface, and transferring the thermal energy to the fluid flowing through the collector.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
PERFORMANCE COMPARISION BETWEEN RECTANGULAR PARALLEL FLOW AND COUNTER FLOW MICROCHANNEL HEAT EXCHNAGER[ ]


The study of heat transfer rate, effectiveness, performance index and effectiveness are calculated between counter flow and parallel flow microchannel heat exchanger with varying thickness of separating wall were calculated. The rectangular type 3D isosceles right triangular microchannel is taken for the study. The water is taken as working fluid for both hot and cold fluid.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Status of use of Internet and Soft Technology in Small Business[ ]


The use of internet and soft technology has been predicted to be the new drivers of economic growth for developing countries. The micro small and medium enterprises (MSMEs) sector play a significant role in the economic growth of both developed as well as developing countries. This sector in India represents the most significant share in productive units and employment generation; the current government policy directions address the ways and means of developing the capacities of MSMEs.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
EFFECT OF TOOL PARAMETERS ON FSW JOINT OF 6082 AL ALLOY BY TAGUCHI METHOD[ ]


Friction stir Welding is the type of welding used as a solid state joining process (below melting point) for materials that is different alloys of aluminum, magnesium etc. and also for hard materials like steels. The effects of various parameters of FSW welding process like rotational speed, depth of cut, feed rate, probe diameter, shoulder diameter, welding speed have been investigated to reveal their Impact on welding joint using Taguchi Methodology.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Centrifugal Pump working as turbine in various water resources at Uttarakashi in Uttarakhand[ ]


Hydro power is a renewable energy resources.In the Himalayan State Hydro power is the main power generation because of availability of water in the various areas.Uttarakhand is one of the Himalayan State in India where various water resources are available.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Thermal analysis and Optimization of Thermal Barrier Coated Diesel Engine Piston using Taguchi method[ ]


In the present study, three different coating materials, coated on the top surface of diesel engine piston (AlSi) with different thermal properties are taken: yttria- partially stabilized zirconia (Y-PSZ), Mullite ((Al6Si2O13) and Silicon Dioxide (SiO2). Thermal analysis is carried out for a high temperature conditions using ANSYS 15.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Electrical and Thermal performance of solar photovoltaic thermal Energy Collection System With Rib Rouhgness[ ]


In this work, a parametric study of the enhancement achieved in electrical (cell) efficiency and thermal efficiency of providing roughness on the underside of the absorber plate. The performance parameters (enhancement of electrical efficiency and thermal efficiency ).

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
ANALYSIS ON “A YEAR ROUND COMFORT SYSTEM”[ ]


In this Paper the two technology has been implemented on an air cooler so as to make the system more functional in both winter and summer. And the Technologies are Indirect Evaporative cooling (IEC)& Direct evaporative cooling (DEC).The functional system is capable to reduce the humidity of air.While doing experimental analysis results on an average about 15% reduction in humidity observed as a result.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
STUDY AND EXAMINE THE GO-KART WORKING MECHANISM[ ]


Generally, go-kart is a very fun to drive, it works on a simple structure about the chassis which is base of go-kart is made by different type of materials (alloy steel), after that this car includes various types of I.C engines according to the power consumption. Mostly go karts uses clutch system for that transmission is attached to engine at rear axle.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
The effects of ethanol-unleaded gasoline blends on engine performance and pollutant emission in a Spark-Ignition engine[ ]


The purpose of this study is to experimentally investigate the effect of ethanol and unleaded gasoline blended with0%, 5%, 10 % and 15% on the performance and pollution emission of a spark-ignition engine.In Performance tests we calculated fuel consumption, engine torque, brake power, brake thermal efficiency and brake specific fuel consumption.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Investigation of Issues in designing and development of an overhead Bike[ ]


This paper discusses anoverhead bike which brings theRevolution in automobile and aerialvehicles. This bike is meant for commercial use and defence i.e. during rescue operations, spying and lifting a person to a higher altitude etc.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design and Fabrication of Abrasive Jet Machine[ ]


Abrasive Jet Machine is a non-conventional machining process. In Abrasive Jet Machining Process the material removal is done from the work piece with the help of high speed abrasive particles. The abrasive particle may consist of Silicon, Alumina and many more.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
ANALYTICAL THERMAL ANALYSIS ON STRAIGHT TRIANGULAR FINS[ ]


Thermal behaviour of Triangular fin is analytically investigated using first principle. An analytical closed form solution of the problem under-consideration is obtained manually since the governing equations and their boundary conditions are linear. The results of this study show that MATLAB can be used effectively and efficiently to solve challenging heat transfer problems.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Computational analysis of solid tube with & without fin using Altair CFD tool Acusolve[ ]


The study of natural convection from a heated tube having conical fin configuration using CFD tool Acusolve has been carried out and material under consideration is aluminium and the free stream fluid is air. The velocity distribution showing the convection loops formed around the heated tube surface.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Study of the Effects of Random Inclusions in Composite Construction with Isotropic Negative Poisson’s Ratio[ ]


Materials with negative Poisson’s ratio (NPR) effects have been reviewed and conclude that the studies have mainly focused on 2D periodic structures which only have NPR effects in certain in-plane directions. In this paper, composite structures with isotropic NPR effects using NPR random inclusions is developed by Ansys software.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Design & Analysis of F1 Racing Car using CAE Tools[ ]


The main objective of this work is to design and analyze the roll cage of F1 type racing vehicle using CAE tools by taking into account the guidelines as per the SAE SUPRA rule book. The AISI 4130 roll cage is designed and analyzed using Solidworks and Ansys.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
STUDY ON MECHANICAL BEHAVIOUR OF BHIMAL FIBER REINFORCED EPOXY COMPOSITE[ ]


In the present work, the fiber reinforced epoxy composite is fabricated and tested for evaluation of various mechanical properties such as tensile, flexural and impact strength. In this project, composite is made by reinforcing bhimal fiber with epoxy resin.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
IDENTIFICATION OF LEAN MANUFACTURING STATUS IN LOCOMOTIVE MANUFACTURING INDUSTRY- A CASE STDUY[ ]


The technology during the 21st century offers a great promise to the people all over the world. The latest advances in Engineering Science and technology have given engineers powerful tools fore-assessing and reorganizing the systems. The present study has been undertaken for analyzing different types of wastes in a Diesel Locomotive Plant’s Carbon Brush shop with an aim to design strategies for developing and implementing a Lean Manufacturing Program in such machine shops.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Numerical Investigation of Shell and Tube Heat Exchanger for Heat Transfer Optimization[ ]


An un-baffled shell-and-tube heat exchanger design with respect to heat transfer coefficient and pressure drop is investigated by numerically modelling. The flow and temperature fields inside the shell and tubes are resolved using a commercial CFD package considering the plane symmetry. For single shell and tube bundle is compared experimentally with CFD simulation.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Exergetic Analysis of Solar Air Heater: A Review[ ]


Solar energy is a clean, most exuberant and freely available renewable source of energy. Due to lower value of convective heat transfer coefficient (h), thermal performance of solar air heater does not take into account.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Experimental Investigation of Mechanical properties of Bagasse Ash and SiC reinforced Al 7075 alloy matrix hybrid composites manufactured by stir casting method[ ]


In present investigation, The fabrication of Al alloy 7075 based matrix hybrid composites with reinforcement particals of sugarcane bagasse-ash with varying (3%,6%,9%) percentage and SiC 3% is constant.

------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Pages   [1] [2]